SciELO - Scientific Electronic Library Online

 
vol.36 número2ENSAYOS MECÁNICOS SOBRE MORTEROS CON AGREGADOS DE PLÁSTICO RECICLADO DOSIFICADOS SEGÚN MODELO DE CONDUCTIVIDAD TÉRMICACONTENIDO DE PLOMO, CADMIO Y ARSÉNICO EN TEJIDOS BIOLÓGICOS DE LA PALOMA COMÚN (Columba livia) PRESENTES EN UN ÁREA URBANA PREVIAMENTE CONTAMINADA CON RESIDUOS MINEROS índice de autoresíndice de materiabúsqueda de artículos
Home Pagelista alfabética de revistas  

Servicios Personalizados

Revista

Articulo

Indicadores

Links relacionados

  • No hay artículos similaresSimilares en SciELO

Compartir


Revista internacional de contaminación ambiental

versión impresa ISSN 0188-4999

Rev. Int. Contam. Ambient vol.36 no.2 Ciudad de México may. 2020  Epub 04-Mayo-2021

https://doi.org/10.20937/rica.53541 

Artículos

PRODUCTION OF LOW-COST BIOCOMPOSITE MADE OF PALM FIBERS WASTE AND GYPSUM PLASTER

PRODUCCIÓN DE BIOCOMPUESTOS DE BAJO COSTO A PARTIR DE DESHECHOS DE FIBRA DE PALMA Y YESO

Wissem Gallala1  * 

Hisham Mustafa Mohamed Khater2 

Marwa Souilah3 

Khamsa Nouri3 

Mohamed Ben Regaya4 

Mohamed Essghaier Gaied1 

1University of Sousse, ISBAS, Station Square 4000 Sousse, Tunisia

2Housing and Building National Research Center, Giza, Egypt

3Faculty of Sciences of Gabes, Erriadh City, 6072 Zrig Gabes, Tunisia

4CTMCCV, Lacagna Street 1009, Ouardia, Tunis, Tunisia


ABSTRACT

In recent years, natural fibers have been increasingly employed in building materials, due to their proprieties for manufacturing low-cost, renewable, and eco-friendly composites. This study aimed to develop a biocomposite based on local materials: natural fibers and plaster. The natural fibers used are date palm fibers waste from Gabes oasis, Tunisia. In order to characterize these materials, many properties were investigated experimentally (i.e., size, thermal behavior, and microstructural characteristics). On the biocomposite samples, compressive and flexural strength, as well as water absorption tests were performed, properties which increased with the addition of fiber wastes. In order to improve the composite durability, chemical treatments with sodium hypochlorite and resin coating were carried out to decrease surface tension and improve adhesion with the plaster matrix. As a result, the biocomposite showed satisfactory physical, thermal, and mechanical performances, which qualify it as a thermal insulation building material.

Key words: biomass; plaster; alkaline treatment; physical and mechanical properties

RESUMEN

En años recientes, las fibras naturales se han empleado de manera creciente en materiales de construcción debido a sus propiedades para manufacturar compuestos resistentes, de bajo costo y amigables con el ambiente. Este estudio tuvo como propósito desarrollar un biocompuesto a partir de materiales locales: fibras naturales y yeso. Las fibras naturales utilizadas son fibras de desecho de palmas de dátiles del oasis de Gabes, Túnez. Con el fin de caracterizar estos materiales se investigaron de manera experimental muchas de sus propiedades (por ejemplo, tamaño, comportamiento térmico y características microestructurales). En las muestras de biocompuestos se llevaron a cabo pruebas de resistencia estructural y a la compresión, así como de absorción de agua, propiedades que se incrementaron con la adición de fibras de desecho. Con el fin de prolongar la durabilidad del biocompuesto se realizaron tratamientos químicos con hipoclorito de sodio y recubrimiento de resina para disminuir la tensión superficial y mejorar la adhesión a la matriz de yeso. Como resultado, el biocompuesto tuvo un desempeño físico, térmico y mecánico satisfactorio, que lo califica como material viable para aislamiento térmico en la construcción.

Palabras clave: biomasa; yeso; tratamiento alcalino; cualidades físicas y mecánicas

INTRODUCTION

Nowadays cellulose fibers are widely used for reinforcement of mortar, concrete, and polymer composites. Cellulose fiber composites are considered as alternative and competitive materials compared with glass and carbon composites due to their low density, good mechanical properties, eco-friendly nature and low investment cost. Furthermore, the physical and mechanical properties of composites can be improved by chemical treatment (Alawar et al. 2009, Alsaeed et al. 2013, Iucolano et al. 2015, Achour et al. 2017, Oushabi et al. 2017) or by adding a suitable resin to the matrix during its fabrication procedure (Hamzaoui et al. 2014, Fiore et al. 2015, Atiqah et al. 2017, Ghofrani et al. 2017).

In this regard, there are several available works in literature on the use of cellulose fiber materials as reinforcement for concrete and mortar. The natural fibers materials which have been investigated are mainly banana (Iucolano et al. 2015, Mukhopadhyay and Bhattacharjee 2016), bamboo (Agarwal et al. 2014, Javadian et al. 2016, Khatib and Nounu 2017), alfa (Khelifa et al. 2016), flax (Yan and Chouw, 2013, Yan et al. 2014), date palm (Kriker et al. 2005, Benmansour et al. 2014, Djoudi et al. 2014, Boumhaout et al. 2017), etc. Most of these studies revealed that date palm fibers are very promising reinforcing materials and can be used as thermal insulation materials in building.

In Tunisia, the oasis areas, which include cultivated land covered around 45 000 ha in 2010 (Ben Salah 2014). Every year after the date fruit harvesting, a considerable amount of date palm wastes is accumulated in huge mounds that ultimately cause environmental problems. In 2006, a total of 90 000 t of agricultural wastes were generated in oases (ANGED 2006). Palm leaflets are traditionally used to make utensils and basketworks (Hamza et al. 2013). Nowadays the by-products and waste of date palm are also used as a component for compost preparation (Bchini et al. 2002, Sghairoun and Ferchichi 2011, Latigui et al. 2013, El Khaldi et al. 2016).

In the construction sector the uses of these wastes are very limited, however they possess attractive properties compared to synthetic fibers. The valorization of this vegetable waste in the development of the construction sector has several objectives: economic, technical and environmental. Its abundance in nature and mechanical and thermal properties makes possible to classify it among the strategic resources of renewable energies (Sumathi et al. 2007).

Furthermore, gypsum deposits outcrop in thick layers in southern Tunisia and many plaster manufactures are installed in this region. The produced plaster is mainly used for decorative purposes, although it has interesting thermal properties (Mansour et al. 2013). In the present study, the effect of date palm fibers waste (DPFW) as reinforcing agent on the mechanical properties of plaster-based composite was investigated. The results of an alkaline treatment and drying temperature have also been studied.

EXPERIMENTAL STUDIES

Materials

Plaster

The plaster (DecoM2) used in this study was provided by the SIPS company and is ISO 9001 certified. The setting behavior of the plaster was characterized by common penetration procedures (knife cut for the initial setting and 40 shore C for the final setting) according to French standard NF B12-401. The grain size distribution was determined using wet sieving (Table I). The physical and mechanical properties of used plaster are presented in table II and figure 1.

TABLE I GRAIN SIZE DISTRIBUTION OF THE STUDIED PLASTER 

Grain size Percentage
+ 250 µm ≤ 0.2 %
-250 + 150 µm 1 to 2.5 %
-150 + 090 µm 12 to 17 %
-90 + 063 µm 22 to 28 %

TABLE II PHYSICAL PROPERTIES OF THE STUDIED PLASTER 

Parameter Value
Initial setting (min) 13
40 shore ºC for final setting (min) 30
Compressive strength (MPa) 9.2
Flexion strength (MPa) 4.2
Water absorption (%) 35
Porosity (%) 38

Fig. 1 Different steps of the experimental protocol 

Palm date fibers

The ground palm wastes were provided by Chenini Oasis Backup Association, Gabes. Two types of treatment were applied to the raw fibers. In the first one, sodium hypochlorite was used for 2 h, and the second one consisted of impregnation in an NaOH solution at various concentrations (1 %, 2 % and 4 %) for 24 h. The incorporated fibers were treated in order to clean the surface from impurities and to protect it against water.

The thermal analysis of biomass was conducted in a thermogravimetric analyzer (model SETARAM). The DTG curve (Fig. 2) revealed three distinct endothermic peaks corresponding to the decomposition of palm waste:

  • In the first zone (25-200 ºC) endothermic evaporation of residual water occurred, corresponding to a mass loss of absorbed moisture of approximately 1 %.

  • The second zone (200-300 ºC) is characterized by significant mass loss (about 3.5 %) due to hemicellulose decomposition (Yang et al. 2004).

  • The third zone (300-400 ºC) corresponds to the stage of decomposition of cellulose.

Fig. 2 Thermal analysis of date palm fibers. Thermogravimetry (TG) in mg = sample loss weight during heating (green curve); DTG/mg/min = the first derivative of TG (purple curve); DSC = differential scanning calorimetry (heat flow/µv; blue curve). Horizontal axis is temperature (ºC) 

The decomposition of lignin took place over a wide range of temperatures up to 400 ºC (Nasser et al. 2016). The microstructures of the palm fiber show that its surface is irregular with many filaments, impurities and pores (Fig. 3a, c).

Fig. 3 Microstructure of date palm fibers (a and c) before and (b and d) after alkaline treatment 

Analytical methods

The gypsum composite was prepared using variable mass proportions of DPFW (7, 10, 15, 17, and 20 %). To measure the mechanical strengths, standard prismatic test pieces of 4 × 4 × 16 cm were manufactured with a constant water plaster ratio (W/P) of 0.65. These tests were conducted at ages of 3, 7 and 28 days. The capillary water absorption coefficient of hardened mortar was determined according to the BS EN 1015-18 method of test. In order to determine the thermal conductivity of the samples, a Taurus TLP300 Thermal Conductivity Analyzer was used.

RESULTS AND DISCUSSION

Mechanical strength

The results of flexural strength are presented in figure 4a, b. There were not relevant effects of the fibers on the flexural strength from day 3 to 28, except for the sample incorporating 17 % of fibers in the formulation. The last sample shows an enhancement in mechanical properties at different ages compared to the reference composite. At day 28, the improvements were approximately 11 % for this sample.

Fig. 4 Flexural and compressive strength results of tested composites. (a and c) Before washing; (b and d) after washing 

The results of the compression tests before and after washing are presented in figures 4c and 3d, respectively. An increase in the compressive strength is noted for all composites compared to the control mortar. At day 28, the compressive strength of the composite with 17 % of fibers was 26 % higher than the reference without fibers. The amelioration in the compressive strength is also attributed to a better fiber-matrix adhesion, since fibers become rougher and thinner after cleaning with water, which may improve their adhesion ability with the matrix (Sawsen et al. 2015).

The addition of 17 % of fibers with different lengths influences the rheological behavior of the plaster. The reduced flexural strength is generally caused by the loss of maneuverability, which is due to poor distribution of the fibers in the fresh state and leads to increasing porosity. Concerning the compressive strength, there is a slight improvement, reaching a maximum for fiber lengths of 20 mm and then a slow decrease for the lengths of 30 and 40 mm (Fig. 5). This decrease may be due to unsuitable compactness and workability caused by excess of fibers in the mixture.

Fig. 5 Effects of fiber length on the mechanical strength 

Alkaline treatment

From the previous tests, we found that an addition of 17 % of fibers gives the best results in terms of flexural and compressive strengths. Hence, we incorporated this percentage of fibers in order to develop the resto of the tests.

The mechanical properties of the studied fibers before and after the treatment with different percentages of NaOH are shown in table III. An improvement in the flexural strength of the DPFW was observed when the alkali treatment was applied. This enhancement can be explained by the removal of the significant parts of lignin, hemicelluloses, wax and oils covering the external surface of the fibers (Li et al. 2007). This modification facilitates the rearrangement of fibrils (Fig. 3b, d) along the direction of flexural deformation. Furthermore, the improvement of strength can be due to the increase of cellulose content and the compactness of the fibers (Sathishkumar et al. 2013).

TABLE III INFLUENCE OF NaOH TREATMENT ON THE FLEXURAL STRENGTH 

NaOH concentration (%) Flexural strength (MPa)
Composite 1 1 3.980
Composite 2 2 5.156
Composite 3 4 5.859

Water absorption

Figure 6 shows a correlation between the increasing percentages of DPFW, which tend to increase water absorption. Increasing the percentages of DPFW from 7 to 20 % in the plaster mortar resulted in an increase of water absorption. This behavior is attributed to the porosity of fibers and their hydrophilic character, which is mainly due to the presence of hemicelluloses.

Fig. 6 Water absorption behavior of the studied biocomposite 

Plaster tiles of dimension 300 x 300 x 20 mm were made. After immersion in water, the differences in water absorption were minimal (Table IV). However, the absorption increases respectively to 34.84 and 34.41 % for the specimen reinforced with DPFW and for treated fibers. The treatment with epoxy resin decreases water absorption. This decrease is due to the surface modifying treatment and thereby, hydrophilic behavior is relatively reduced (Sreekala et al. 2002).

TABLE IV WATER ABSORPTION OF COMPOSITES MADE WITH UNTREATED AND TREATED FIBERS 

Sample Control sample (plaster without date palm fibers waste) 17 % fibers 17 % fibers + epoxy resin
Water absorption (%) 34.05 34.84 34.41

Comparison with natural insulating composites

Table V shows the comparison of thermal conductivity of some composites made with natural fibers and used as construction materials for thermal insulation. The experimentally measured values indicate that the prepared composite in this study presents an excellent thermal performance compared to other composites, as shown in the literature.

TABLE V COMPARISON OF THERMAL CONDUCTIVITY AND DENSITY OF DPFW WITH SOME MATERIALS USED FOR THERMAL INSULATION IN THE BUILDING 

Composite Thermal conductivity (W/mK) r kg/m3 References
Plaster + 17% DPFW 0.52 1415.15 This study
Gypsum neat 0.44 1130 Chikhi et al. 2013
Date palm 0.072-0.085 187- 389 Asdrubali et al. 2015
Plaster concrete 0.89 1890 Djoudi et al. 2014
Plaster concrete + 2 % DPFW 0.76 1200 Djoudi et al. 2014
Concrete + cork 10 % 0.96 2100 Panesar et al. 2012

DPFW: date palm fibers waste composites

According to Djoudi et al. 2014, the thermal conductivity decreases when fiber content increases. The recent study elaborated by Braiek et al. 2017 mentioned that this composite material has good thermophysical properties and can be used in walls or false ceilings. Furthermore, the length of the fibers influences the thermal conductivity; the composite made with short fiber produces many voids, hence leading to low thermal conductivity. The studied composite can be considered as a lightweight material. This value is in the range of data reported in the literature on aggregate concrete, which varied from 0.3 to 0.6 W/mK. This indicates a promising potential for the development of efficient and safe building insulation materials.

Effect of drying temperature

The rheological behavior shows the same evolution at a drying temperature of 40 and 60º C. The flexural and compressive strengths increase with the drying time (Fig. 7). However, these parameters exhibit a large drop for a drying time of 24 h at 80 ºC (flexural = 0.234 MPa, compression = 3.65 MPa).

Fig. 7 Flexural and compressive strength results of tested composites under different drying temperatures 

The increase of mechanical properties can be explained by the acceleration of the curing mechanism of the plaster induced by drying temperature and the increase of fiber-matrix adherence. Nevertheless, high temperature (80 ºC) leads the release of volatiles, discoloration and poor mechanical properties.

CONCLUSION

This experimental study investigated the incorporation of DPFW as reinforcement in a plaster matrix. After carrying out several tests, the optimal percentage of fibers was 17 %, and the length was 20 mm.

The incorporation of DPFW improves mechanical strength with the increasing percentage and length of the fibers compared to a control plaster without them. However, a slight reduction was recorded for a certain percentage due to the loss of workability and lousy orientation of the fibers and the same results for the compressive strength.

The treatment with NaOH showed an enhancement in the rheological properties (flexion and compression) of the biocomposite and reduced the retardation effect by removing impurities and some soluble compounds. Furthermore, the epoxy treatment effectively contributed to reducing water absorption. The physical properties showed more porous and hydrophilic fibers, possessing high absorption capacity.

In the second part of the experimental study, the drying test at different temperatures on the reinforced-fiber plaster had the following results:

The flexural and compressive strength increased progressively as a function of time, which can be explained by the development of plaster hardening and the increase adhesion between matrix and fiber.

It was demonstrated experimentally that the addition of 17 % DPFW produced a composite with k = 0.52 Wm-1K-1 and r = 1415 kg m-3. According to these results, the studied biocomposite can be used as sustainable insulation material in building structures.

ACKNOWLEDGMENTS

The authors acknowledge the staff of Centre Technique des Matériaux de Construction, de la Céramique et du Verre (CTMCCV) for their assistance in the realization of this work.

REFERENCES

Achour A., Ghomari F. and Belayachi N. (2017). Properties of cementitious mortars reinforced with natural fibers. J. Adhes. Sci. Technol. 31 (17), 1938-1962. DOI: 10.1080/01694243.2017.1290572 [ Links ]

Agarwal A., Nanda B. and Maity D. (2014). Experimental investigation on chemically treated bamboo reinforced concrete beams and columns. Constr. Build. Mater. 71, 610-617. DOI: 10.1016/j.conbuildmat.2014.09.011 [ Links ]

Alawar A., Hamed A.M. and Al-Kaabi K. (2009). Characterization of treated date palm tree fiber as composite reinforcement. Compos. Part B-Eng. 40, 601-606. DOI: 10.1016/j.compositesb.2009.04.018 [ Links ]

Alsaeed T., Yousif, B.F. and Ku H. (2013). The potential of using date palm fibers as reinforcement for polymeric composites. Mater. Design. 43, 177-184. DOI: 10.1016/j.matdes.2012.06.061 [ Links ]

ANGED (2006). Rapport d’activité sur la valorisation des déchets végétaux en Tunisie. Agence Nationale de Gestion des Déchets. Report. Tunis, Tunisia, 86 pp. [ Links ]

Asdrubali F., D’Alessandro F. and Schiavoni S. (2015). A review of unconventional sustainable building insulation materials. Sustain. Mater. Techn. 4, 1-17. DOI: 10.1016/j.susmat.2015.05.002 [ Links ]

Atiqah A., Jawaid M., Ishak M.R. and Sapuan S.M. (2017). Effect of alkali and silane treatments on mechanical and interfacial bonding strength of sugar palm fibers with thermoplastic polyurethane. J. Nat. Fibers. 15 (2), 251-261. DOI: 10.1080/15440478.2017.1325427 [ Links ]

Bchini H., Hsayoui S. and Aloui S. (2002). Gestion de la matière organique et compostage des palmes sèches dans le milieu oasien. Annales de l’INRAT 75, 299-312. [ Links ]

Benmansour N., Agoudjil B., Gherabli A., Kareche A. and Boudenne A. (2014). Thermal and mechanical performance of natural mortar reinforced with date palm fibers for use as insulating materials in building. Energ. Buildings 81, 98-104. DOI: 10.1016/j.enbuild.2014.05.032 [ Links ]

Ben Salah M. (2014). Valorisation et recyclage des sous-produits des oasis: acquis et perspectives. Observatoire du Sahara et du Sahel [online]. http://projet.oss-online.org/ftp/MENA-DELP/Etudes-MENADELP/OSSMENA-DELP_Produits-Oasiens.pdf 30/05/2018. [ Links ]

Boumhaout M., Boukhattem L., Hamdi H., Benhamou B. and Nouh F.A. (2017). Thermomechanical characterization of a bio-composite building material: Mortar reinforced with date palm fibers mesh. Constr. Build Mater. 135, 241-250. DOI: 10.1016/j.conbuildmat.2016.12.217 [ Links ]

Braiek A., Karkri M., Adili A., Ibos L. and Nasrallah S.B. (2017). Estimation of the thermophysical properties of date palm fibers/gypsum composite for use as insulating materials in building. Energ. Buildings 140, 268-279. DOI: 10.1016/j.enbuild.2017.02.001 [ Links ]

Chikhi M., Agoudjil B., Boudenne A. and Gherabli A. (2013). Experimental investigation of new biocomposite with low cost for thermal insulation. Energ. Buildings 66, 267-273. DOI: 10.1016/j.enbuild.2013.07.019 [ Links ]

Djoudi A., Khenfer M.M., Bali A. and Bouziani T. (2014). Effect of the addition of date palm fibers on thermal properties of plaster concrete: experimental study and modeling. J. Adhes. Sci. Technol. 28 (20), 2100-2111. DOI: 10.1080/01694243.2014.948363 [ Links ]

El Khaldi R., Daami-Remadi M. and Cherif M. (2016). Biological control of stem canker and black scurf on potato by date palm compost and its associated fungi. J. Phytopathol. 164 (1), 40-51. DOI: 10.1111/jph.12423 [ Links ]

Fiore V., Di Bella G. and Valenza A. (2015). The effect of alkaline treatment on mechanical properties of kenaf fibers and their epoxy composites. Compos. Part B-Eng. 68, 14-21. DOI: 10.1016/j.compositesb.2014.08.025 [ Links ]

Hamza S., Saad H., Charrier B., Ayed N. and Charrier-El Bouhtoury F. (2013). Physico-chemical characterization of Tunisian plant fibers and its utilization as reinforcement for plaster-based composites. Ind. Crop. Prod. 49, 357-365. DOI: 10.1016/j.indcrop.2013.04.052 [ Links ]

Hamzaoui R., Guessasma S., Mecheri B., Eshtiaghi A.M. and Bennabi A. (2014). Microstructure and mechanical performance of modified mortar using hemp fibres and carbon nanotubes. Mater. Des. 56, 60-68. DOI: 10.1016/j.matdes.2013.10.084 [ Links ]

Ghofrani M., Ashori A. and Mehrabi R. (2017). Mechanical and acoustical properties of particleboards made with date palm branches and vermiculite. Polym. Test. 60, 153-159. DOI: 10.1016/j.polymertesting.2017.03.028 [ Links ]

Iucolano F., Caputo D., Leboffe F. and Liguori B. (2015). Mechanical behavior of plaster reinforced with abaca fibers. Constr. Build. Mater. 99, 184-191. DOI: 10.1016/j.conbuildmat.2015.09.020 [ Links ]

Javadian A., Wielopolski M., Smith I.F. and Hebel D.E. (2016). Bond-behavior study of newly developed bamboo-composite reinforcement in concrete. Constr. Build. Mater. 122, 110-117. DOI: 10.1016/j.conbuildmat.2016.06.084 [ Links ]

Khatib A. and Nounu G. (2017). Corrugated bamboo as reinforcement in concrete. P. I. Civil. Eng. Str. B. 170 (4), 311-318. DOI: 10.1680/jstbu.16.00067 [ Links ]

Khelifa M.R., Leklou N., Bellal T., Hebert R.L. and Ledesert B.A. (2016). Is alfa a vegetal fiber suitable for making green reinforced structure concrete? Eur. J. Environ. Civ. En. 22 (6), 1-21. DOI: 10.1080/19648189.2016.1217792 [ Links ]

Kriker A., Debicki G., Bali A., Khenfer M.M. and Chabannet M. (2005). Mechanical properties of date palm fibres and concrete reinforced with date palm fibers in hot-dry climate. Cement Concrete Comp. 27 (5), 554-564. DOI: 10.1016/j.cemconcomp.2004.09.015 [ Links ]

Latigui A., Choi J.M. and Regagba Z. (2013). Use of palm (Poenix dactilyfera L.) fiber and sewage sludge co compost as substrates in soilless crop system. Pak. J. Biol. Sci. 16 (14), 651-660. DOI: 10.3923/pjbs.2013.651.660 [ Links ]

Li X., Tabil L.G. and Panigrahi S. (2007). Chemical treatments of natural fiber for use in natural fiber-reinforced composites: A review. J. Polym. Environ. 15 (1), 25-33. DOI: 10.1007/s10924-006-0042-3 [ Links ]

Mansour M.B., Soukaina C.A., Benhamou B. and Jabrallah S.B. (2013). Thermal characterization of a Tunisian gypsum plaster as construction material. Energy Procedia 42, 680-688. DOI: 10.1016/j.egypro.2013.11.070 [ Links ]

Mukhopadhyay S. and Bhattacharjee B. (2016). Influence of fibre dispersion on compression strength of banana fibres reinforced concrete. J. Ind. Text. 45 (5), 957-964. DOI: 10.1177/1528083714545394 [ Links ]

Nasser R.A., Salem M.Z., Hiziroglu S., Al-Mefarrej H.A., Mohareb A.S., Alam M. and Aref I.M. (2016). Chemical analysis of different parts of date palm (Phoenix dactylifera L.) using ultimate, proximate and thermo-gravimetric techniques for energy production. Energies 9 (5), 374. DOI: 10.3390/en9050374 [ Links ]

Oushabi A., Sair S., Hassani F.O., Abboud Y., Tanane O. and El Bouari A. (2017). The effect of alkali treatment on mechanical, morphological and thermal properties of date palm fibers (DPFs): Study of the interface of DPF-Polyurethane composite. South African J. Chem. Eng. 23, 116-123. DOI: 10.1016/j.sajce.2017.04.005 [ Links ]

Panesar D.K. and Shindman B. (2012). The mechanical, transport and thermal properties of mortar and concrete containing waste cork. Cement Concrete Comp. 34, 982-992. DOI: 10.1016/j.cemconcomp.2012.06.003 [ Links ]

Sathishkumar T.P., Navaneethakrishnan P., Shankar S., Rajasekar R. and Rajini N. (2013). Characterization of natural fibers and composites-A review. J. Reinf. Plast. Comp. 32 (19), 1457-1476. DOI: 10.1177/0731684413495322 [ Links ]

Sawsen C., Fouzia K., Mohamed B. and Moussa G. (2015). Effect of flax fibers treatments on the rheological and the mechanical behavior of a cement composite. Constru. Build. Mater. 79, 229-235. DOI: 10.1016/j.conbuildmat.2014.12.091 [ Links ]

Sghairoun M. and Ferchichi A. (2011). Composting heap palm tree’s products in southern Tunisia. J. Environ. Sci. Eng. 5, 886-889. DOI: 10.17265/1934-8932/2011.07.013 [ Links ]

Sreekala M.S., Kumaran M.G. and Thomas S. (2002). Water sorption in oil palm fiber reinforced phenol formaldehyde composites. Compos. Part A: Appl. S. 33(6), 763-777. DOI: 10.1016/S1359-835X (02)00032-5 [ Links ]

Sumathi S., Chai S.P. and Mohamed A.R. (2008). Utilization of oil palm as a source of renewable energy in Malaysia. Renew. Sust. Energ. Rev. 12 (9), 2404-2421. DOI: 10.1016/j.rser.2007.06.006 [ Links ]

Yan L. and Chouw N. (2013). Behavior and analytical modeling of natural flax fiber reinforced polymer tube confined plain concrete and coir fiber reinforced concrete. J. Compos. Mater. 47, 33-48. DOI: 10.1177/0021998312454691 [ Links ]

Yan L., Chouw N. and Jayaraman K. (2014). Flax fiber and its composites-a review. Compos. Part B Eng. 56, 296-317. DOI: 10.1016/j.compositesb.2013.08.014 [ Links ]

Yang H.P., Yan R., Chin T., Liang D., Chen P. and Zheng C. (2004). Thermogravimetric analysis-Fourier transform infrared analysis of palm oil wastes pyrolysis. Energ. Fuel 18 (6), 1814-1821. DOI: 10.1021/ef030193m [ Links ]

Received: February 01, 2019; Accepted: September 01, 2019

*Corresponding author: wissem.gallala@fsg.rnu.tn

Creative Commons License This is an open-access article distributed under the terms of the Creative Commons Attribution License